|
Product Details:
Payment & Shipping Terms:
|
| Name: | Motor Drying Oven | Max Temperature: | 200 Degree Celcius |
|---|---|---|---|
| Working Size: | 1500×2000×1500mm(W×H×D) | Application: | Insulatin Curing Of Motors |
| Rated Voltage: | 3P 380V 50HZ | Warranty: | 12 Months |
| High Light: | Motor Coil Baking Motor Drying Oven,50HZ Motor Drying Curing Oven,Electric Motor Drying Curing Oven |
||
Industrial Electric Motor Drying Oven, Curing Oven for Motor Coil Baking
1.Working Principle
The motor drying oven is a special motor drying equipment with hot air circulation
and automatic intelligent control of the whole process. The top of the motor curing
oven is equipped with a large air volume, low noise and temperature resistant centrifugal
fan, The heating chamber is set in the air ducts on both sides of the inner liner.
When working, the air is supplied vertically from the lower part of the left and right
air ducts (about 1 / 3 height) in the working chamber, so that the parts are heated
from all directions. After full heat exchange between the hot air in the working
chamber and the workpieces, the hot air evenly flows back to the top suction
chamber, and then is sent to the air ducts on both sides (heating chamber)
through the fan for heating again. This cycle repeats all the time. The forced
hot air circulation is carried out by the circulation fan with large air volume
and high air pressure so as to ensure the good temperature uniformity in the
working chamber. The temperature in the vacuum impregnation process
can meet the process requirements.
This motor baking oven has the characteristics of high temperature control precision,
simple operation, energy saving, high safety and reliability.Vacuum pressure impregnation
plant is widely used in coil impregnation drying (curing) process of motor
industry and curing after epoxy dry casting.
2.Main Techical Parameters
| Item | Curing Oven |
| Q’ty | 1 set |
| Working size | 1500×2000×1500mm(W×H×D) |
| Overall size |
2000×2800×1900mm (excluding external parts) |
| Working temperature | Room temperature～200℃ |
| Temperature uniformity | ≤±3％(at highest temperature) |
| Heating power | 45kw |
| Divided into 2 groups; automatically power cut off at holding stage so as to save energy. | |
| Fan power | 1.1Kw×2 sets |
| 1 set for left and right separately | |
| Transmission system |
Manual cart:1500×1500mm, 1 set; Guide rail: Q235 10# light rail; wheel: 4 pcs; Frame: Q235 6# sqaure tube or angle steel with antirust treatment. Also there is a riffled plate resin dripping plate. |
3.Structure
| Oven Body | |
| Structure type | Integral type |
| Door opening method | Right-left door. |
| Shell | Q235 cold rolled steel plate with surface phosphating treatment, and acrylic sefl-drying paint is used. |
| Inner layer | It is made of Q235 cold rolled steel plate. Before welding, the steel surface is sprayed with w61 series silicone heat-resistant paint (400 ℃). |
| Shell framework | It is made of Q235 channel steel and angle steel. Before welding, the steel surface is treated with rust removal and rust prevention. |
| Inner layer framework | It is made of Q235 steel. Before welding, the steel surface is derusted and degreased, and then sprayed with w61 series silicone heat-resistant paint (400 ℃). |
| Base tray |
It is made of Q235 channel steel. After rust removal and antirust treatment, 851 moisture-proof paintis sprayed on the surface
|
| Heat preservation material | Adopt the quality silicate aluminum cotton. |
| Sealing material | Asbestos rope and silicone rubber plate are used for sealing the door and oven body, and asbestos belt is used for sealing the fan. |
| Electrical System | |
| control cabinet | Independent cabinet |
| Power supply | 3N+PE 380V 50Hz |
| Alarm | Domestic digital temperature control alarm, temperature sensor PT100 |
| Protection system |
One set of over temperature alarm system. When the temperature in the oven is abnormal, it will send out sound and light alarm, and automatically cut off the heating power. b) Motor overloading protection to prevent motor burning and tripping. c)Protect electric heater from short circuit. Schneider brand. d) The heating components are controlled by solid state relay. Miguel electric. e)The motor and heating interlock device. The blower should be started first, and after that the heater can be turned on. f) Control circuit protection to prevent circuit short circuit and accident. g) Air switch to prevent the main circuit overloading and short circuit, causing accidents. |
Notes: Unmentioned points should be according GB5170-85 and JB/T5520-91 standard.
Vaccum Pressure Impregnation Equipment before the drying Oven of Motors:
Contact Person: Ms. Ruth
Tel: +0086 15305299442
